Nationals at Richmond Yacht ClubMay 20 - 22
Result
PosBoatTotalRace 1Race 2Race 3Race 4Race 5Race 6Race 7
1Peaches184(4)3(7)4(11)4(15)1(16)1(17)2 (19)
2Motorcycle Irene181(1)2(3)3(6)3(9)5(14)3(17)3 (20)
3Under the Radar237(7)1(8)1(9)1(10)3(13)5(18)5 (23)
4Hot Sheet242(2)4(6)3(9)4(13)2(15)2(17)7 (24)
5Magic Bus303(3)5(8)5(13)6(19)6(25)4(29)1 (30)
6Bombora516(6)7(13)8(21)5(26)4(30)15(45)6 (51)
7Fired Up!5412(12)8(20)6(26)8(34)9(43)7(50)4 (54)
8Freaks on a Leash579(9)9(18)7(25)7(32)7(39)9(48)9 (57)
9Abigail Morgan628(8)11(19)10(29)9(38)10(48)6(54)8 (62)
10Dianne7510(10)10(20)9(29)DNS(45)12(57)8(65)10 (75)
11Artemis765(5)6(11)12(23)DNS(39)11(50)10(60)DNF (76)
12Public Enemy8012(12)12(24)11(35)10(45)8(53)14(67)11 (78)
13Tequila Mockingbird8811(11)14(25)14(39)11(50)14(64)11(75)13 (88)
14Current Affair8814(14)12(26)13(39)12(51)13(64)12(76)12 (88)
15Phoenix10715(15)RET(31)RET(47)DNS(63)15(78)13(91)DNF(107)
export csv

GPS Tracks
[ Upload a GPS Track ]

Regatta Message Board

Reply | Post New Message | All Messages | this message is spam
Author: Joe B
Subject: Rudder Bearings
Info: (13910 views) Posted: Monday 2-9-15 01:05:15 PM
$163 for a standard set which Buzz said fits most Expresses. These did not fit my hull#100. Inside diameters to0 tight and I believe upper bearing was too tall.

$75 dollars to recut them to my specs that I measured with a caliper.

This is my second set of bearings. First new ones lasted about 9 years. 1st time I took the rudder to Buzz to measure rudder post. All fit well except the upper bearing was too tall, so I shaved that down myself since height tolerance is not absolutely critical on the upper.

Any excessive up and down movement will wear the bearing out, so Buzz provided for few upper washers in different thicknesses.

My first set, I sealed in the lower with some 3M 4200, but not the 5200 stuff (others reported hard to remove later). The 4200 adhesion did not last despite a good prep and repeated application a few years later. I believe there is not much for the adhesive to grab onto except the top of edge of the lower bearing. I used silicone to hold in place the upper bearing.

This second set I did not use any adhesive since the outside diameters are pretty snug.

I would like to hear from others about about sealing the bearings.

Joe B.

:: What is the cost of the bearing as i am sure i could use
:: a set

:: chris
::
::
:: :: I need new rudder bearings. Called Buzz Ballenger and
:: :: said he will make new one if he gets a minimum order for
:: :: five sets.
:: ::
:: :: I placed an order. Need four more. Anyone else need a
:: :: set?
:: ::
:: :: Call Buzz Ballenger 831) 763-1196.

Reply | Post New Message | All Messages | this message is spam