Nationals at Richmond Yacht ClubMay 20 - 22
Result
PosBoatTotalRace 1Race 2Race 3Race 4Race 5Race 6Race 7
1Peaches184(4)3(7)4(11)4(15)1(16)1(17)2 (19)
2Motorcycle Irene181(1)2(3)3(6)3(9)5(14)3(17)3 (20)
3Under the Radar237(7)1(8)1(9)1(10)3(13)5(18)5 (23)
4Hot Sheet242(2)4(6)3(9)4(13)2(15)2(17)7 (24)
5Magic Bus303(3)5(8)5(13)6(19)6(25)4(29)1 (30)
6Bombora516(6)7(13)8(21)5(26)4(30)15(45)6 (51)
7Fired Up!5412(12)8(20)6(26)8(34)9(43)7(50)4 (54)
8Freaks on a Leash579(9)9(18)7(25)7(32)7(39)9(48)9 (57)
9Abigail Morgan628(8)11(19)10(29)9(38)10(48)6(54)8 (62)
10Dianne7510(10)10(20)9(29)DNS(45)12(57)8(65)10 (75)
11Artemis765(5)6(11)12(23)DNS(39)11(50)10(60)DNF (76)
12Public Enemy8012(12)12(24)11(35)10(45)8(53)14(67)11 (78)
13Tequila Mockingbird8811(11)14(25)14(39)11(50)14(64)11(75)13 (88)
14Current Affair8814(14)12(26)13(39)12(51)13(64)12(76)12 (88)
15Phoenix10715(15)RET(31)RET(47)DNS(63)15(78)13(91)DNF(107)
export csv

GPS Tracks
[ Upload a GPS Track ]

Regatta Message Board

Reply | Post New Message | All Messages | this message is spam
Author: Mike Bruzzone
Subject: Use Braces
Info: (15341 views) Posted: Friday 5-14-10 09:40:03 AM
Hi, Yes, the sling lifting trianglur strap in the bildge is NOT a single point lifting point . . . requiring two braces from top of sling to rail (each side) back by the primaries or farther aft for maximum bracing leverage.

I would not cut up the boat; personally.

My sling is 4 of 5 Star tensil chain with large stainless shakles on each end.

The Up end has one piece of high strength lined attached to the top shackly (mid length) using a cow hitch . . . and carbiner hooks on each tail. . . one on each for attachement to perforated toe rail. Always hook Carbiners gate up to take the max load.

Same arranegemebnt is used for boats with T track rails & cars for attachement . . . or U bolts thru deck at brace attach points; port & starboard.

mb

:: I presume the boat was set up for a three point bridal
:: so it would be stable while suspended.
::
:: We had a nylon lift strap made with a shackle for the
:: strap on the keel bolts, up through the port to a point
:: about 1-1/2 feet above the deck. There's a heavy steel
:: ring on the top end of the main strap. Two smaller nylon
:: straps come off that same ring and are sized to center
:: the main strap in the port with the boat level. They
:: have carabiners at the deck end and these clip to the
:: toe rail outboard of the winches.
::
:: I cant see why a 6 inch port wouldn't work. Just
:: remember there needs to be a clearance cutout on the
:: front edge of the hatch for the port.
::
:: Bob Harvey
::
:: :: We just recently purchased an E27. Could anyone tell me
:: :: why the port for the hoisting strap doesn't align with
:: :: the strap. There must be some reason for this. I read an
:: :: earlier post discussing how two extra lines secured to
:: :: the toe line near the winches are required to center the
:: :: strap through the hole.
::
:: :: The former owner of this boat obviously did not realize
:: :: this as there is damage to the deck at the port.
:: ::
:: :: I am planning on cutting out the damage and putting a
:: :: 6" port instead. Is there any reason I could not do
:: :: this?
:: ::
:: :: Mark

Reply | Post New Message | All Messages | this message is spam