Nationals at Richmond Yacht ClubMay 20 - 22
Result
PosBoatTotalRace 1Race 2Race 3Race 4Race 5Race 6Race 7
1Peaches184(4)3(7)4(11)4(15)1(16)1(17)2 (19)
2Motorcycle Irene181(1)2(3)3(6)3(9)5(14)3(17)3 (20)
3Under the Radar237(7)1(8)1(9)1(10)3(13)5(18)5 (23)
4Hot Sheet242(2)4(6)3(9)4(13)2(15)2(17)7 (24)
5Magic Bus303(3)5(8)5(13)6(19)6(25)4(29)1 (30)
6Bombora516(6)7(13)8(21)5(26)4(30)15(45)6 (51)
7Fired Up!5412(12)8(20)6(26)8(34)9(43)7(50)4 (54)
8Freaks on a Leash579(9)9(18)7(25)7(32)7(39)9(48)9 (57)
9Abigail Morgan628(8)11(19)10(29)9(38)10(48)6(54)8 (62)
10Dianne7510(10)10(20)9(29)DNS(45)12(57)8(65)10 (75)
11Artemis765(5)6(11)12(23)DNS(39)11(50)10(60)DNF (76)
12Public Enemy8012(12)12(24)11(35)10(45)8(53)14(67)11 (78)
13Tequila Mockingbird8811(11)14(25)14(39)11(50)14(64)11(75)13 (88)
14Current Affair8814(14)12(26)13(39)12(51)13(64)12(76)12 (88)
15Phoenix10715(15)RET(31)RET(47)DNS(63)15(78)13(91)DNF(107)
export csv

GPS Tracks
[ Upload a GPS Track ]

Regatta Message Board

Reply | Post New Message | All Messages | this message is spam
Author: Jason
Subject: Jib Halyard Sheave Trouble
Info: (12422 views) Posted: Thursday 12-27-07 09:20:54 PM
Ok. A few boats do have a third halyard. If it were me, I would just use the two original sheaves. It's up to you.

-Jason 

:: Jason,
::
:: On Magic, the Jib halyard currently exits the mast below
:: the forestay pin. Above the forestay pin are two sheaves
:: that are occupied by the #1 spin halyard and the #2 spin
:: halyard. Should we remove the old #2 spin halyard and
:: use that for our jib halyard and not worry about the
:: "original sheave"?
::
:: :: Mike,
:: ::
:: :: Sounds like you still have the original sheaves in the
:: :: mast. You want to give Ballanger spars a call and have a
:: :: couple new ones sent to you. The original ones are for
:: :: wire halyards and will start eating up your nice
:: :: high-tech halyards.
:: ::
:: :: To answer your question though, you are probably going
:: :: to want to drop the mast to replace them. Both halyards
:: :: and the forestay ride on the same pin. So, to replace
:: :: the sheave you need to remove the shaft (pin) that goes
:: :: through both sheaves and the forestay eye. It can be
:: :: tricky to thread the needle through all three items with
:: :: the mast down, with the mast up would be very
:: :: interesting. I suppose it could be done if you held the
:: :: mast in place with the topping lift, but I would not
:: :: recommend it.
:: ::
:: :: One hint, when installing the new shives make sure you
:: :: use a small piece of line looped around the groove of
:: :: the sheave, as if it were a halyard running around the
:: :: sheave. If you don't you will likely drop the sheave
:: :: inside the mast and spend several hours trying to fish
:: :: it out of the mast. Ask me how I know this!
:: ::
:: :: Cheers,
::
:: :: Jason
:: ::
:: :: :: Our jib halyard sheave is very hard to turn. The sheave
:: :: :: appears to be intact, but is showing metal fillings on
:: :: :: both side as if it is not seated properly, although it
:: :: :: looks square to the mast top halyard entrance. How do I
:: :: :: take it apart to replace it? DO I need to drop the
:: :: :: Mast???
:: :: ::
:: :: :: Mike
:: ::
:: :: :: #80
:: ::
:: :: :: Magic

Reply | Post New Message | All Messages | this message is spam