Berkeley Mid Winter #4 at Berkeley Yacht ClubFebruary 9
Result
PosBoatTotalRace 1
1Dan Pruzan Wile E Coyote11
2Motorcycle Irene22
3Bessie Jay33
4Freaks ona Leash44
5Mirage55
6Libra66
7Dianne77
8Wetsu88
9Take Five99
10Elise1010
11Abigail Morgan1111
12Strega1212
14Great White14DNC
14Opa!14DNC
14Peaches14DNC
14Eagle14DNC
14Magic Bus14DNC
export csv

Regatta Message Board

Reply | Post New Message | All Messages | this message is spam
Author: Mike Bruzzone
Subject: Lifting strap/braces
Info: (15587 views) Posted: Sunday 5-16-10 09:01:12 AM
Hi Maryann . . . I'm not sure about using the winches to attach the braces . . . without a backing plate down below (not necessarily fender washers) . . . someone else who does might want to chime in on their time tested experience attaching directly to winches.

I also do not cross sheet winches . . . because their not angled to pull in toward the center of the boat . . . and you can see this action tweek the deck in toward center at winches . . . although for hositing the boat, likely a situation with less weight.

mb

:: I have the triangular lifting arrangement but have been
:: attaching to the winches (several wraps w/ half
:: hitches), since I removed the toerail. Is there any
:: reason why I shouldn't be doing this?
::
:: Also, it seems to be difficult to keep the main strap
:: centered in the port throughout the lifting process.
:: Does anyone have any suggestions?
::
::
:: :: Hi, Yes, the sling lifting trianglur strap in the bildge
:: :: is NOT a single point lifting point . . . requiring two
:: :: braces from top of sling to rail (each side) back by the
:: :: primaries or farther aft for maximum bracing leverage.
:: ::
:: :: I would not cut up the boat; personally.
:: ::
:: :: My sling is 4 of 5 Star tensil chain with large
:: :: stainless shakles on each end.
:: ::
:: :: The Up end has one piece of high strength lined attached
:: :: to the top shackly (mid length) using a cow hitch . . .
:: :: and carbiner hooks on each tail. . . one on each for
:: :: attachement to perforated toe rail. Always hook
:: :: Carbiners gate up to take the max load.
:: ::
:: :: Same arranegemebnt is used for boats with T track rails
:: :: & cars for attachement . . . or U bolts thru deck at
:: :: brace attach points; port & starboard.
:: ::
:: :: mb
:: :: :: I presume the boat was set up for a three point bridal
:: :: :: so it would be stable while suspended.
:: :: ::
:: :: :: We had a nylon lift strap made with a shackle for the
:: :: :: strap on the keel bolts, up through the port to a point
:: :: :: about 1-1/2 feet above the deck. There's a heavy steel
:: :: :: ring on the top end of the main strap. Two smaller nylon
:: :: :: straps come off that same ring and are sized to center
:: :: :: the main strap in the port with the boat level. They
:: :: :: have carabiners at the deck end and these clip to the
:: :: :: toe rail outboard of the winches.
:: :: ::
:: :: :: I cant see why a 6 inch port wouldn't work. Just
:: :: :: remember there needs to be a clearance cutout on the
:: :: :: front edge of the hatch for the port.
:: :: ::
:: :: :: Bob Harvey
:: :: ::
:: :: :: :: We just recently purchased an E27. Could anyone tell me
:: :: :: :: why the port for the hoisting strap doesn't align with
:: :: :: :: the strap. There must be some reason for this. I read an
:: :: :: :: earlier post discussing how two extra lines secured to
:: :: :: :: the toe line near the winches are required to center the
:: :: :: :: strap through the hole.
:: :: ::
:: :: :: :: The former owner of this boat obviously did not realize
:: :: :: :: this as there is damage to the deck at the port.
:: :: :: ::
:: :: :: :: I am planning on cutting out the damage and putting a
:: :: :: :: 6" port instead. Is there any reason I could not do
:: :: :: :: this?
:: :: :: ::
:: :: :: :: Mark

Reply | Post New Message | All Messages | this message is spam